Porch Ceiling, Door and Trim

November 5-15, 2020

Next up was the ceiling of the porch. The original house had ceilings and interior walls made of classic pine beadboard. I selected some that had the remains of a blue wash paint. Here they are laid out to get a good scrub because once they are on the ceiling they won't see water again.

These are attached with 1-1/2" staples from my pneumatic stapler. Since the beadboard is only 1/4" thick, staples work much better than screws or brads. The tricky part of this work is getting the tongue-and-groove to seat well for the entire length. The technique I use is to get something that will fit into the groove of the board being installed then leverage against the outer 2x4 to push it really tight into the board that is already up at each rafter point before stapling it. Doing it by myself made me wish I had one or even two more arms.

It was time for the last really difficult part of this project: hanging the door. I was given a beautiful entry door by Bob E, a cycling friend that was also the source for the sliding glass doors used for the skylights. The door's original frame was broken up in the salvage process, so I needed to create a new door frame. I first saw how this was done by John D. in Santa Fe 40 years ago and I've done it maybe twice since then. When you buy a new door it comes "pre-hung" which is a great convenience, so my guess is there aren't that many finish carpenters who ever do this.

The first step is to build a frame that will fit the door with about 1/2" to 3/4" to spare. Inside the frame you put stops 2-3/4" from the edge (since this is a 2-1/2" thick door); the stops in this case are 1/2" thick. This creates a lip all the way around that is smaller than the door dimensions. Setting the door on the frame allows marking the precise location of the hinges:


Now its possible to chisel out the material from the frame to allow the hinge to be inset. One of the great inventions during the course of my lifetime is the Fein Multimaster AKA "Multi-tool" but which I call "power chisel." If you don't have one already, you need one! With the saw attachment this thing allows you to precisely chisel out the wood, blissfully ignorant of the angle of the grain which always made hand-chiseling a total pain for me. For any hope of success with an old fashion chisel you need to have it super sharp and I've never risen to that level of fastidiousness.

Here is the result after screwing the hinges into the frame. You can try the door opening/closing action and make adjustments so it's right:

To prepare the wall to get the frame, I added 1" lumber on both sides and a 2x4 on top to narrow the rough opening about 1" wider and 1/2" taller than the outside dimensions of the frame. Since the rough opening is likely not perfectly square and vertical, you want to give some room for adjustment between rough opening and frame. Its just about impossible to work with the frame when the heavy door is in it so you pop the hinge pins, set the 80 pound door aside, and install the frame into rough opening. Using a level and square, you get the position correct then push shims into the gap between the frame and rough opening to hold it securely just so, then you screw through the shims to fasten it with substantial 3-1/2" screws. The olden style is to use a 20 penny hot-dip galvanized finish nail and set it well, which is where the saying "dead as a door nail" comes from. (Using screws is better for those of us that can't be trusted to do the right thing on the first pass.) 

You can see the lighter colored shims in this picture:

Now you can try the door swing, verticality, fit of the latch, etc. Quite a bit of the behavior can be controlled by adjusting the shims.
 

After trimming down and taping the edges of the Tyvek the building starts to feel quite tight when you shut the door:

With the door in the wall I could now finish up the siding.  I started with the peak on the north side. Again I learned from my experience on the south side moving the ladder back and forth that it was worth the time to set up a little scaffold:

As for the siding on either side of the door, as I was saying above, the old house had lots of short pieces of siding and after rummaging around in the used pile I found most of what I needed already cut pretty close or right on the length required.

You can see that I've included an outdoor electrical outlet to make it easier to use electric garden gear, like our mini rototiller. Of course I haven't got power in the building but its a comin'. 

The visit from Quality Control didn't go too well since I hadn't been paying much attention to the alignment of siding lines as it wraps around the corner. Luckily its all up with screws so not too much trouble to take it down, add a partial board at the bottom, and reinstall.

I'll agree that's more pleasing to the eye, and the electrical outlet is now 4 inches higher, which I suspect will be more convenient.

All that was left for the exterior were the following finishing touches: 

  • Apply trim to the door.
  • Fit the top piece of siding on each side around the eaves which requires cutting out slots for the 10 rafters out of one board.
  • Apply trim to the building corners.
Thinking why it took two solid days to complete that list: excessive pickiness and used materials. For example despite an extensive search, all the used trim on hand was two or more inches short of what I needed for the door.  So I settled on some rough cut 1x3 Douglas Fir that was left from the house project. The fuzzy, sliver-loaded rough cut isn't good right next to the door since its a high-touch area. When I took the boards to the DeWalt planer, it wouldn't respond to the on-off switch. After a couple hours electrical diagnosis on the planer without success (I think the motor was invaded by a critter - all they have to do is chew through one motor wire), I used the Jointer instead to get a somewhat smooth surface. The "mix and match" look is now pretty extreme:
Here is a detail shot of where the siding meets the roof rafters. Each cutout from the siding has to be the right distance apart so the board will slide up around all of them at once:

That of course requires a few round trips back to the saw to adjust notches to perfection.

For the corner trim I didn't worry about piecing together used boards because the junction is under the eave so stays dry. Final pictures for outside:



That's looking pretty darn rustic now. Perhaps it will get a coat of white paint someday, but that's out of scope for this project. Its just a tool shed after all.


PS. The Door Knob Saga

Let me draw your attention to the knob in the pictures at the end of the post above vs. the first time the door is shown in place. The earlier photos have the matching handle and deadbolt which are the original hardware that was on the salvaged door. High quality stuff made by Schlage.  Unfortunately it did not occur to me to ask friend Bob for keys when I salvaged the door. I asked if he still had any of those keys around; he searched through his various key stashes and mailed an identical pair of keys with some effort involved (first attempt returned for insufficient postage). However, although they were Schlage keys, they were not the Schlage keys. "No biggie," I thought, "I don't really need a lockable shed." So I proceeded to mount the lock as you see in the first pictures.

The thing about high quality door hardware is that its loaded with features. In this case the inside side of the handle had a push-button lock mechanism that would "lock until the next time the door is opened" by a simple push, and "keep it locked after opening" with a push-in-and-turn maneuver.  It was within the first five times I shut the door that I unknowingly bumped the inside of the handle and ended up locked out. Luckily there was enough play in the door to be able to push the door in and use the old credit-card trick to retract the catch.

So the approach of having a lockable but not unlockable door wasn't going to work. Bummer. I considered the option of installing a push rod override to manually push in the latch from outside. That idea was dismissed after some experimenting and the realization that it was just too Robert (over rigged aka a hack).

When Bob heard the news that his keys hadn't fit he suggested that a locksmith could make a key for the lock. So I took the unit to Asheville. In order to make a key the smith has to extract the tumbler. But the thing about high quality door hardware is that it has an anti-theft feature that makes it so you can't take the knob apart without having the key in the lock to rotate it! Dead end. So on my way home I stopped by Home Depot and acquired the cheapest door handle they had, which is what you see in the later photos.

But wait! There's more!

As the observant reader will note in the final post of this blog, the finished shed has the original hardware! Some days or weeks later a connection occurred to me. The keys Bob had sent were identical, and that had probably seemed right enough to him because the deadbolt and the door handle probably used the same key! I took the deadbolt off the door and it was obviously going to be much easier to disassemble; there is no high-quality anti-theft protection needed there because deadbolts are much more securely fastened to the door.

So it was back to the locksmith, this time with both units. They showed me how the tumbler is extracted without having all the springs pop out. Then how the key pins could be measured to get a key code which is then used to make a key. I knew something about lock mechanisms before, but now I really understand it. Purpose built tools, dexterity and fastidious attention are the table stakes if you want to work on locks. The key made for the deadbolt worked in there and it worked in the door handle as hoped! The locksmith bill, including a spare copy, was under $20 - just slightly more than the cheapest door handle I could find at Home Depot. Thanks and praises to Al Odom Locksmith in Asheville!

Comments