Posts

Why a Shed? What a Shed!

Image
Early September 2020 Long on The List has been a tool / potting shed for Charla's garden. Our corn crib currently is the closest thing to the garden but it is very awkward to use and is mostly filled with firewood. When used to keep tools dry, they generally end up in a heap on either side of a step-down-into-it doorway. And when you want firewood you generally end up tripping over tools. Several trips for firewood coinciding with the advent of Charla's birthday without any big present ideas finally pushed this project to the top of the list. The southern end of the flattish spot where the main garden lies is demarcated by an intermittently running branch bordered by several trees including a large ash. This shades that end of the garden, making it unsuitable for planting. So we have a natural spot for a tool shed at garden level (avoiding going up or down hill sounds better and better with age). Starting with a basic concept of something a bit larger than 8' x 8', we ...

Site Prep and Layout

Image
  September 19 - 20, 2020 I neglected to get a picture of the untouched grass before I started in with the backhoe. Oh well. This picture isn't too far into the process: The big ash tree on the right had some bigish roots running through the soil. I've got a rough outline of the building staked there so I can get a sense of what is level. It became clear pretty early on that the grade was going to make for at least two steps to get into the building if I built it above grade. So ( change of plans! ) lets excavate  down to make the building level below grade at the uphill side. That of course requires some kind of retaining wall there, which ultimately will be the weak spot for this building after a few decades. After a considerable additional amount of digging the next day, I found there was a huge rock in the southeast corner. It wasn't going anywhere and wasn't persuadable with a cold chisel.  So that became the de-facto lower limit of the "foundation." Afte...

Floor and Wall Framing

Image
September 20-22, 2020 Next up was doing a materials run to Summit Lumber Co. That required making a stab at materials requirements using some chicken scratches: Having loaded up the truck with materials and the credit card with a total approaching four digits (lumber ain't cheap these days!), I got started on placing the cement piers and primary support joists. Then leveraged my hanger nail gun for the second time ever to hang the floor joists: Next I applied the tongue and groove 3/4" plywood to form the deck. I regretted later not having put some blocking between the joists since it ended up a little spongy after I'd put on the plywood.   I dug through our house construction leftovers from 12 years ago and found most of a gallon of Spar Varnish which I applied immediately to the plywood since what would normally be a subfloor is going to be the floor floor. Put it on before you get it dirty so you get a pretty nice looking surface that is somewhat waterproof. After lett...

Porch it

Image
September 23 - October 1, 2020 When I replaced the culvert in the driveway right below this shed project, I ran into a couple large rocks.  One of them had a squarish character although it was at the upper end of what my Kuboto Tractor could push around. It had been sitting next to the driveway for a couple years where I'd frequently notice it. While doing the groundwork, it occurred to me that this might be a good stoop stone / step stone to get into the shed. And... it could be the front support of the porch so I wouldn't have those butt-ugly cement piers right out there in front. Both the front end loader and the backhoe attachment on the tractor come in handy for this kind of effort. The front end loader can get the rock in the general right location but doesn't provide any dexterity. The backhoe isn't big enough to pick up a rock that size but it can lift an edge, push a corner down and otherwise make it possible to get the rock into the right place in all three d...

Roof Frame and Sheath

Image
  October 2-13, 2020 As you could see by my last post I'd used plastic sheeting to keep the rain off, but getting a roof over it is critical to prevent damage to the work in progress. I started with the longest board in the project, a 17'6" ridge pole. They don't carry 18' at the lumber yard so I had to settle for a 20' --- it's always fun to figure out how to carry that in the truck! Placing that board finalizes the slope of the roof. The plan was for a 6/12 roof pitch, but I cut those uprights for 6/12 not taking into account the 3-1/2" height of the ridge pole itself so the pitch ended up more like a 7/12 which is fine because I had not already ordered my roof metal with 6/12 measurements. Then cutting the roof rafters is just a matter of reminding myself how to use a roofing square embossed with all kinds of tables but the basic angles are just from the rulers on the sides - duh! You can see its all 2x4 material - not strong enough for any real con...

Roofing and Skylights

Image
October 14-24, 2020 A patch of rainy weather delayed progress and created a layer of slip mud over the construction site. I attempted to minimize the wallow formation by laying out cardboard --- with partial success since the cardboard tended to slide around when I stepped on it. The first step of roofing is getting up the drip edge flashing onto the eaves, fastened with 3/4" roofing nails. Short nails and bouncy eave boards led to a few lightly hammered fingertips and choice words. You always have to take a few extra nails up there with you to account for the ones that inevitably get away. Starting on the higher west side, I created a jig of sorts to make up for the lack of a second pair of hands. This is accomplished by screwing some scrap 2x4 to the ends of the rafter tails so they extend beyond the eaves by the amount I want the roofing to overhang. To those I screw a cross 2x4x12 board thereby creating a stop which can hold the roofing before I get it screwed d...