Porch it

September 23 - October 1, 2020

When I replaced the culvert in the driveway right below this shed project, I ran into a couple large rocks.  One of them had a squarish character although it was at the upper end of what my Kuboto Tractor could push around. It had been sitting next to the driveway for a couple years where I'd frequently notice it. While doing the groundwork, it occurred to me that this might be a good stoop stone / step stone to get into the shed. And... it could be the front support of the porch so I wouldn't have those butt-ugly cement piers right out there in front.

Both the front end loader and the backhoe attachment on the tractor come in handy for this kind of effort. The front end loader can get the rock in the general right location but doesn't provide any dexterity. The backhoe isn't big enough to pick up a rock that size but it can lift an edge, push a corner down and otherwise make it possible to get the rock into the right place in all three dimensions. Here is a picture of its close-to-final placement:

It's pretty tricky work. The rock has to be the right distance from and somewhat aligned with the building. It has to be the right height to support the porch - with a 1/2" to 1" drop so any water that gets on the porch runs away from the building. And because it isn't really a flat rock - its got some wedge action going there -  the back has to be dropped so that the front doesn't tilt too much. By "dropped" I mean the rock has to be lifted on one side, then dirt removed to make a nest, then lowered back down and "encouraged" with the backhoe bucket.  After seeing how it looks, making test step ups and downs, then repeating the process a few times you decide it's as good as it's going to get.

Rock in place, the next task is to frame the porch floor on top of it. The porch is built with treated lumber which isn't the material typically chosen by woodcarvers, but carving is what is called for to place a level 2"x6" across that very lumpy rock. However given an afternoon to spare and a portable sawzall, one can fit things:


Its hard to see in the fading-light above but the 2x6 across the front is whittled down to about 3.5" to get over the rock. The corners of the porch are cantilevered, which on the downhill side makes the porch just the right height to sit on.

Next up (so to speak): the porch ceiling with post-and-beam supports.  The next morning I started by screwing some spare 2"x4"x12' to the edge of the main building so I had a support and guide - right length, right height:
 
Then I rooted around in the barn for the best of the 4"x4" stock salvaged from the old Norton house. It had a porch wrapped around two sides with 4x4 supports every 6 feet, but most of them had damage at the bottom end so selection was required. And it was hard to find an appropriate board to go across the front. After searching for a while I found exactly one American Chestnut 2x4 that was just long enough to cover the front of the 4x4's coming off the building (to avoid end-grain showing) but .... as I was trying to notch the chestnut using the chop saw, the end of the board fell off the saw stand and ZIP!!! - the board was now too short to span the end-grain. Curses ensued. Still long enough to go between the 4x4s so I guess the end grain is going to show. It's what I get for using the wrong tool for the job.

Here's the post-and-beam structure complete, still being supported by the twelve footers on the building.
 


Among my leftovers from the studio construction project was a bit of Tyvek. Charla suggested I might as well use it here.  Which is a good idea because during the winter we occasionally get a real dry powered snow and with the help of the wind, it will find its way through any crack in the siding and dust all the contents inside. After I wrapped the building I had less than two feet of material left. That's the way I like to (un)roll!

The last step is to frame in the porch ceiling which helped stiffen up the whole thing some - but even with those boards it is still pretty wobbly. I don't really want to put angle braces on those porch posts (which is what is called for) because its not that tall so some folks might bump their heads on them. My hope is that if the building is rock solid (eventually) then it will anchor the porch framing.
 

Comments